Обновление прошивки EXOS на коммутаторах Summit Extreme
1. Проверяем версию прошивки:
SummitX450-24x.1 # show version Switch : 800187-00-02 0651G-00157 Rev 2.0 BootROM: 1.0.3.1 IMG: 11.6.3.5 XGM-2xn-1 : Image : ExtremeXOS version 11.6.3.5 v1163b5 by release-manager on Sun Sep 9 10:46:16 PDT 2007 BootROM : 1.0.3.1
и
SummitX450-24x.1 # show switch Current State: OPERATIONAL Image Selected: primary Image Booted: primary Primary ver: 11.6.3.5 Secondary ver: 11.6.3.5 Config Selected: primary.cfg Config Booted: primary.cfg
Из этого видно, что в коммутаторе загружена старая прошивка 11.6.3.5 в оба профиля памяти. У меня на данный момент есть рабочая прошивка 15.1.2.12. Буду загружать её в оба профиля.
2. Назначаем коммутатору IP адресс:
SummitX450-24x.1 # configure vlan "Mgmt" ipaddress 10.10.10.200/24
3. Заливаем прошивку в secondary configuration (по дефолту он загружается в primary). 10.10.10.2 – адрес tftp-сервера:
SummitX450-24x.1 # download image 10.10.10.2 summitX-15.1.2.12-patch1-6.xos vr "VR-Mgmt" secondary Do you want to install image after downloading ? (y—yes, n—no, —cancel) Say Yes to install image after downloading
Debug information files are present in internal-memory. These files will be removed if you continue with download. Do you want to continue with download and remove existing files from internal-memory? (y/N) Yes Do you want to install image after downloading? (y - yes, n - no, - cancel) Yes Downloading to Switch... 8< skip 8< ... Installing to primary partition! Installing to Switch... 8< skip 8< ... Image installed successfully This image will be used only after rebooting the switch!
4. Заливаем ssh:
SummitX450-24x.1 # download image 10.10.10.2 summitX-15.1.2.12-patch1-6-ssh.xmod Do you want to install image after downloading ? (y—yes, n—no, —cancel) Say Yes to install image after downloading SummitX450-24x.1 # run update SummitX450-24x.1 # restart process "thttpd" SummitX450-24x.1 # enable ssh2
5. Переключаемся в secondary для возможности заливки в primary:
SummitX450-24x.1 # use configuration secondary SummitX450-24x.1 # use image secondary SummitX450-24x.1 # reboot
6. Заливаем прошивку в primary configuration:
SummitX450-24x.1 # download image 10.10.10.2 summitX-15.1.2.12-patch1-6.xos vr "VR-Mgmt" primary Do you want to install image after downloading ? (y—yes, n—no, —cancel) Say Yes to install image after downloading
7. Заливаем ssh:
SummitX450-24x.1 # download image 10.10.10.2 summitX-15.1.2.12-patch1-6-ssh.xmod Do you want to install image after downloading ? (y—yes, n—no, —cancel) Say Yes to install image after downloading SummitX450-24x.1 # run update SummitX450-24x.1 # restart process "thttpd" SummitX450-24x.1 # enable ssh2
8. Переключаемся в primary:
SummitX450-24x.1 # use configuration primary SummitX450-24x.1 # use image primary SummitX450-24x.1 # reboot
После перезагрузки можем убедится что залита новая прошивка командами show switch и show version. На этом обновление EXOS завершено.
Comments
So empty here ... leave a comment!